-
Featured User: kurt
Open-source hardware project hosting is my passion. I spend most of my free time building neat gadgets or planning what I'll build next. I love building things, and I want to make Open Hardware Hub a place that inspires others to build, ...
-
Updates 2013 February 18
It's been a while, hasn't it? Well, that's ok because we've got a lot of updates to talk about. Most of these have been effective on the site fora couple weeks now. A few may or may not be active when this article gets posted, but they'll certainly be applied in the ...
Portal Turret Plushie
Files
- Portal_Turret.pde - Portal Turret Arduino Sketch
- PIRSensorTest.pde - PIR Sensor Test Arduino Sketch
- WaveShieldTest.pde - Wave Shield Test Arduino Sketch
- test.wav - Test WAV File
- Pattern Page 1.pdf - Rear and Center Pattern
- Pattern Page 2.pdf - Front Pattern
- Pattern Page 3.pdf - Leg and Leg Cover Pattern
Bill of Materials
| Qty | Part # | Description | Schematic ID | Source | |
|---|---|---|---|---|---|
| 1 |
|
Wave Shield | Adafruit Wave Shield for Arduino Kit - v1.1 | Wave Shield | Source |
| 1 |
|
RBBB Kit | Really Bare Bones Board Kit (Arduino Compatible) | RBBB | Source |
| 1 |
|
PIR Motion Sensor | PIR Motion Sensor | PIR Sensor | Source |
| 1 |
|
SD Card 2 GB | SanDisk 2 GB Class 2 SD Flash Memory Card SDSDB-2048-A11 | SD Card | Source |
| 1 |
|
TSW-150-07-L-S | CONN HEADER 50POS .100" SGL GOLD | Header Pins | Source |
| 1 |
|
White Fleece Fabric | 1/4 yard | Source | |
| 1 |
|
Red Tulle Fabric | 1/8 yard | Source | |
| 1 |
|
Black Cotton Fabric | 1/8 yard | Source | |
| 1 |
|
Polyester Fiberfill | 12 ounces | Source | |
| 1 |
|
White Zipper | 7 inches | Source | |
| 10 |
|
WP7113LID | 5MM LOW CURRENT RED LED, LAMP THOLE, BULK | LED | Source |
| 1 |
|
CF14JT100R | 1/4w 100 ohms 5% Carbon Film Resistors | Source | |
| 1 |
|
CF14JT10K0 | 1/4w 10K ohms 5% Carbon Film Resistors | Source | |
| 1 |
|
BH48AASF | HOLDER BATTERY 8 CELL AA W/SNAP | Battery Pack | Source |
| 1 |
|
PSR-23F08S-JQ | Speaker | Speaker | Source |
| 1 |
|
Tilt Sensor | Tilt Sensor | Tilt Sensor | Source |
| 1 |
|
ZMA00A150L04PC | Switch, Snap, Lef Actuated, 4.55mm Long, 50 Grams Oper Force, PC Term, 0.1 Amps | Lift Switch | Source |
| 1 |
|
GF-1123-0009 | Slide Switches STANDARD SPST 11A | Power Switch | Source |
Download BOM w/o images
Download BOM w/ images
Steps
142. Sew zipper to other side
Flip the fabric inside out, and line the unstitched side of the zipper with the unstitched side of the fleece. Sew from the top until just past the zipper.
143. Put fabric shell on electronics skeleton
Flip the fabric right-side out, and carefully slip the fabric over the skeleton of the turret.
144. Stuff with fiberfill
Open the zipper, and use the fiberfill to stuff the turret around the skeleton.
145. Cut leg slits
Cut slits in the front of the fabric so that it fits around the wire legs. Tip: If you need to adjust the cut, simply make another cut and sew up the previous cut.
146. Print out leg pattern
Print out and cut the pattern for the legs and leg covers. When you print these pieces, make sure to set "Page Scaling" to "None" in the "Print" dialogue box.
Download steps w/o images
Download steps w/ images
Revisions
15 - added attribution note
14 - updated description
13 - added a couple switches to the parts list
12 - updated steps 52 and 53 to remove "TK" placeholders
11 - added a speaker to the BOM
10 -
9 -
8 -
7 - edited step 130
6 -
5 -
4 -
3 - updated project images.
2 - added youtube link. updated line numbers.
1 - Initial project release
Add revision
blog comments powered by Disqus
Back
