-
Featured User: kurt
Open-source hardware project hosting is my passion. I spend most of my free time building neat gadgets or planning what I'll build next. I love building things, and I want to make Open Hardware Hub a place that inspires others to build, ...
-
Updates 2013 February 18
It's been a while, hasn't it? Well, that's ok because we've got a lot of updates to talk about. Most of these have been effective on the site fora couple weeks now. A few may or may not be active when this article gets posted, but they'll certainly be applied in the ...
Portal Turret Plushie
Files
- Portal_Turret.pde - Portal Turret Arduino Sketch
- PIRSensorTest.pde - PIR Sensor Test Arduino Sketch
- WaveShieldTest.pde - Wave Shield Test Arduino Sketch
- test.wav - Test WAV File
- Pattern Page 1.pdf - Rear and Center Pattern
- Pattern Page 2.pdf - Front Pattern
- Pattern Page 3.pdf - Leg and Leg Cover Pattern
Bill of Materials
| Qty | Part # | Description | Schematic ID | Source | |
|---|---|---|---|---|---|
| 1 |
|
Wave Shield | Adafruit Wave Shield for Arduino Kit - v1.1 | Wave Shield | Source |
| 1 |
|
RBBB Kit | Really Bare Bones Board Kit (Arduino Compatible) | RBBB | Source |
| 1 |
|
PIR Motion Sensor | PIR Motion Sensor | PIR Sensor | Source |
| 1 |
|
SD Card 2 GB | SanDisk 2 GB Class 2 SD Flash Memory Card SDSDB-2048-A11 | SD Card | Source |
| 1 |
|
TSW-150-07-L-S | CONN HEADER 50POS .100" SGL GOLD | Header Pins | Source |
| 1 |
|
White Fleece Fabric | 1/4 yard | Source | |
| 1 |
|
Red Tulle Fabric | 1/8 yard | Source | |
| 1 |
|
Black Cotton Fabric | 1/8 yard | Source | |
| 1 |
|
Polyester Fiberfill | 12 ounces | Source | |
| 1 |
|
White Zipper | 7 inches | Source | |
| 10 |
|
WP7113LID | 5MM LOW CURRENT RED LED, LAMP THOLE, BULK | LED | Source |
| 1 |
|
CF14JT100R | 1/4w 100 ohms 5% Carbon Film Resistors | Source | |
| 1 |
|
CF14JT10K0 | 1/4w 10K ohms 5% Carbon Film Resistors | Source | |
| 1 |
|
BH48AASF | HOLDER BATTERY 8 CELL AA W/SNAP | Battery Pack | Source |
| 1 |
|
PSR-23F08S-JQ | Speaker | Speaker | Source |
| 1 |
|
Tilt Sensor | Tilt Sensor | Tilt Sensor | Source |
| 1 |
|
ZMA00A150L04PC | Switch, Snap, Lef Actuated, 4.55mm Long, 50 Grams Oper Force, PC Term, 0.1 Amps | Lift Switch | Source |
| 1 |
|
GF-1123-0009 | Slide Switches STANDARD SPST 11A | Power Switch | Source |
Download BOM w/o images
Download BOM w/ images
Steps
11. Solder capacitors
Bend the leads of the capacitors to hold them in place and solder their leads.
12. Insert DIP socket
Insert the DIP (dual in-line package) socket. The divot on the end of socket goes closest to the switch. This lines up with what is printed on the circuit board.
13. Solder DIP socket
Turn the board upside down and set it on something so that it is resting on the DIP socket. I used my diagonal cutters for this. This keeps the socket pushed through the holes while you're soldering. Solder the DIP socket. Solder two diagonal leads first and make sure the socket is fully seated. Then solder the rest of the leads.
14. Insert resonator
Insert the resonator into the three holes marked with a little rectangle. The resonator can be installed wither way. I installed it with the label outwards so I can read it.
Download steps w/o images
Download steps w/ images
Revisions
15 - added attribution note
14 - updated description
13 - added a couple switches to the parts list
12 - updated steps 52 and 53 to remove "TK" placeholders
11 - added a speaker to the BOM
10 -
9 -
8 -
7 - edited step 130
6 -
5 -
4 -
3 - updated project images.
2 - added youtube link. updated line numbers.
1 - Initial project release
Add revision
blog comments powered by Disqus
Back
