-
Featured User: kurt
Open-source hardware project hosting is my passion. I spend most of my free time building neat gadgets or planning what I'll build next. I love building things, and I want to make Open Hardware Hub a place that inspires others to build, ...
-
Updates 2013 February 18
It's been a while, hasn't it? Well, that's ok because we've got a lot of updates to talk about. Most of these have been effective on the site fora couple weeks now. A few may or may not be active when this article gets posted, but they'll certainly be applied in the ...
Portal Turret Plushie
By: kurt
Deadly, yet adorable, this plush turret from the game Portal talks and responds when you play with it. It senses when you pick it up, knock it over, or walk in front of it. The stuffing and soft fleece skin make it super cuddly, too!
Inspired by Up, not North.
Download project description w/o images
Download project description w/ images
Files
- Portal_Turret.pde - Portal Turret Arduino Sketch
- PIRSensorTest.pde - PIR Sensor Test Arduino Sketch
- WaveShieldTest.pde - Wave Shield Test Arduino Sketch
- test.wav - Test WAV File
- Pattern Page 1.pdf - Rear and Center Pattern
- Pattern Page 2.pdf - Front Pattern
- Pattern Page 3.pdf - Leg and Leg Cover Pattern
Bill of Materials
Qty | Part # | Description | Schematic ID | Source | |
---|---|---|---|---|---|
1 | Wave Shield | Adafruit Wave Shield for Arduino Kit - v1.1 | Source | ||
1 | RBBB Kit | Really Bare Bones Board Kit (Arduino Compatible) | Source | ||
1 | PIR Motion Sensor | PIR Motion Sensor | Source | ||
1 | SD Card 2 GB | SanDisk 2 GB Class 2 SD Flash Memory Card SDSDB-2048-A11 | Source | ||
1 | TSW-150-07-L-S | CONN HEADER 50POS .100" SGL GOLD | Source | ||
1 | White Fleece Fabric | 1/4 yard | Source | ||
1 | Red Tulle Fabric | 1/8 yard | Source | ||
1 | Black Cotton Fabric | 1/8 yard | Source | ||
1 | Polyester Fiberfill | 12 ounces | Source | ||
1 | White Zipper | 7 inches | Source | ||
10 | WP7113LID | 5MM LOW CURRENT RED LED, LAMP THOLE, BULK | Source | ||
1 | CF14JT100R | 1/4w 100 ohms 5% Carbon Film Resistors | Source | ||
1 | CF14JT10K0 | 1/4w 10K ohms 5% Carbon Film Resistors | Source | ||
1 | BH48AASF | HOLDER BATTERY 8 CELL AA W/SNAP | Source |
Download BOM w/o images
Download BOM w/ images
Steps
21. Solder SD card slot
Solder the four large flanges on the sides of the slot first. then solder the rest of the small pins that are in the middle of the board. The flanges are for structural support, and the small pins carry electronic signals.
22. Insert resistor
Insert the 10k (brown-black-orange) resistor into the R6 slot. Note: this resistor is too close to IC4. I recommend that you install this resistor after installing IC4 otherwise your IC4 may not seat properly.
23. Solder resistor
Bend the leads so it doesn't fall out when you turn the board over. Solder it in place.
24. Insert resistors
Insert resistors R7 (1.5k, brown-green-red) and R8 (100k, brown-black-yellow) as shown.
Download steps w/o images
Download steps w/ images
Revisions
15 - added attribution note
14 - updated description
13 - added a couple switches to the parts list
12 - updated steps 52 and 53 to remove "TK" placeholders
11 - added a speaker to the BOM
10 -
9 -
8 -
7 - edited step 130
6 -
5 -
4 -
3 - updated project images.
2 - added youtube link. updated line numbers.
1 - Initial project release
Add revision
blog comments powered by Disqus
Back