-
Featured User: kurt
Open-source hardware project hosting is my passion. I spend most of my free time building neat gadgets or planning what I'll build next. I love building things, and I want to make Open Hardware Hub a place that inspires others to build, ...
-
Updates 2013 February 18
It's been a while, hasn't it? Well, that's ok because we've got a lot of updates to talk about. Most of these have been effective on the site fora couple weeks now. A few may or may not be active when this article gets posted, but they'll certainly be applied in the ...
Portal Turret Plushie
Files
- Portal_Turret.pde - Portal Turret Arduino Sketch
- PIRSensorTest.pde - PIR Sensor Test Arduino Sketch
- WaveShieldTest.pde - Wave Shield Test Arduino Sketch
- test.wav - Test WAV File
- Pattern Page 1.pdf - Rear and Center Pattern
- Pattern Page 2.pdf - Front Pattern
- Pattern Page 3.pdf - Leg and Leg Cover Pattern
Bill of Materials
| Qty | Part # | Description | Schematic ID | Source | |
|---|---|---|---|---|---|
| 1 |
|
Wave Shield | Adafruit Wave Shield for Arduino Kit - v1.1 | Wave Shield | Source |
| 1 |
|
RBBB Kit | Really Bare Bones Board Kit (Arduino Compatible) | RBBB | Source |
| 1 |
|
PIR Motion Sensor | PIR Motion Sensor | PIR Sensor | Source |
| 1 |
|
SD Card 2 GB | SanDisk 2 GB Class 2 SD Flash Memory Card SDSDB-2048-A11 | SD Card | Source |
| 1 |
|
TSW-150-07-L-S | CONN HEADER 50POS .100" SGL GOLD | Header Pins | Source |
| 1 |
|
White Fleece Fabric | 1/4 yard | Source | |
| 1 |
|
Red Tulle Fabric | 1/8 yard | Source | |
| 1 |
|
Black Cotton Fabric | 1/8 yard | Source | |
| 1 |
|
Polyester Fiberfill | 12 ounces | Source | |
| 1 |
|
White Zipper | 7 inches | Source | |
| 10 |
|
WP7113LID | 5MM LOW CURRENT RED LED, LAMP THOLE, BULK | LED | Source |
| 1 |
|
CF14JT100R | 1/4w 100 ohms 5% Carbon Film Resistors | Source | |
| 1 |
|
CF14JT10K0 | 1/4w 10K ohms 5% Carbon Film Resistors | Source | |
| 1 |
|
BH48AASF | HOLDER BATTERY 8 CELL AA W/SNAP | Battery Pack | Source |
| 1 |
|
PSR-23F08S-JQ | Speaker | Speaker | Source |
| 1 |
|
Tilt Sensor | Tilt Sensor | Tilt Sensor | Source |
| 1 |
|
ZMA00A150L04PC | Switch, Snap, Lef Actuated, 4.55mm Long, 50 Grams Oper Force, PC Term, 0.1 Amps | Lift Switch | Source |
| 1 |
|
GF-1123-0009 | Slide Switches STANDARD SPST 11A | Power Switch | Source |
Download BOM w/o images
Download BOM w/ images
Steps
7. Insert and solder LED
Insert the LED and make sure that the LED's long lead goes in the hole closest to the (+) printed on the circuit board. Bend the leads so the LED stays in place. Solder the LED.
8. Insert diode, switch, and regulator
Insert the diode, switch and regulator. There is now wrong way to install the switch. The diode's stripe goes near the hole without a ring around it. The flat side of the regulator goes towards the side of the board.
9. Solder LED, diode, switch, and voltage regulator
Solder the LED, diode, switch, and voltage regulator in place.
10. Insert capacitors
Insert the two electrolytic capacitors as shown. Note the position of the stripes on the capacitors to make sure they are inserted correctly.
Download steps w/o images
Download steps w/ images
Revisions
15 - added attribution note
14 - updated description
13 - added a couple switches to the parts list
12 - updated steps 52 and 53 to remove "TK" placeholders
11 - added a speaker to the BOM
10 -
9 -
8 -
7 - edited step 130
6 -
5 -
4 -
3 - updated project images.
2 - added youtube link. updated line numbers.
1 - Initial project release
Add revision
blog comments powered by Disqus
Back
